Male 3" to hosetail 3" 12 24 wneccocp3M90 coupling, compression, thread male 3" to pipe.ext.: 90mm 1 2 wnecirfl3G (3" flange) gasket, 2mm thick rubber, 4 holes 10mm 2 4 wnecirfl3M flange, counterplate, 3 4 plain holes d: 10mm 1 2 wnecirfl3M90 connector,.
The fit and finish of the stock to the action is very nice with good contours for the ejection port and tight fitting all around the action.
300mm 1 1 etoosawsha3N blade BI-metal, for hacksaw, 12 inches, 24 teeth 3 3 etooscdf0620 screwdriver, flat head.5mm x 200mm blade 2 2 etooscisstd1 scissors, standard, 105mm, the pair 1 1 etoosockex2B handle brace, 3/8" square drive 1 1 etoosockj617 socket spanner, 3/8" square.The trigger also breaks very clean and consistent.It utilizes #8-40 screws.The bolt knob is the traditional Remington knob with knurling on top.The top of the action is not clip slotted like the original and the barrel is thicker with a different profile.There is not a wide beavertail style forearm nor is it tall.There is a sling swivel stud up front and one in the rear as well.Body 1 1 etoocuttkn5B blade, for knife/cutter alu 150mm, normal cut 5 5 etoocuttpls3 jack plane "Stanley Surform standard, 250mm blade 1 1 etoocuttplsb spare blade, for "Stanley Surform 250mm 2 2 etoofilehc20 file, half-round, coarse cut, 21 x 200mm 1 1 etoofilenk16 file, needle.The original also used a 1:12 twist but the 1:10 here is more suited to heavier weight bullets like some of the newer 180 grain LR bullets.The action itself is a standard Remington 700 short action that has been blue printed and trued in all of the custom rifle builder ways.Code, description, qty In Each, total qty, aprobootr07.
So if its not recommended for duty as a sniper rifle, where does it stand?
The rifle being reviewed is built by a new company called, appropriately, the.As seen in the picture below, the finish on this M40-66 is much higher quality and the fit and finish is also more precise, which would be expected compared to the non glass bedded, factory produced rifle.300mm 1 2 etoosawsha3N blade BI-metal, for hacksaw, 12 inches, 24 teeth 3 6 etooscdf0620 screwdriver, flat head.5mm x 200mm blade 2 4 etooscisstd1 scissors, standard, 105mm, the pair 1 2 etoosockex2B handle brace, 3/8" square drive 1 2 etoosockj617 socket spanner, 3/8" square.Edge support 25 225 ehdwnutsgh10 NUT, galvanised, for 10 mm diam.As mentioned, the lugs and face are trued, which is obvious when you inspect the bolt.We also shot the rifle off hand where its light weight and slimmer profile worked very well.Bolt 5 45 etoopodgis01 podger, spike to align iron sheet bolt holes 1 9 kwatrepaepli KIT, repair, for rigid water tank epdm rubber liners 1 9 Code Description Qty In Each Total qty wwakrepaepsh epdm material spare, 1 x 1m 1 9 wwakrepaepta adhesif tape.But it certainly is beautiful.We still always use the Federal Gold Medal Match 168gr ammo as our base line test load we use for every 308 rifle review and it performed very well again.